Tuesday, November 17, 2026

Bell & Gossett Pump Shafts

Bell & Gossett Pump Shafts: browse our Bell & Gossett Pump Shafts below. Every shaft listed here is a genuine Bell & Gossett spare, shown with its part number, so you can find the shaft you need for your Bell & Gossett pump. Contact KBS Industries if you need help finding the right part.

Bell & Gossett pump shaft 52-329-573-001 — Bell & Gossett Pump Shafts

Bell & Gossett Pump Shaft
52-329-573-001

Bell & Gossett pump shaft 52-329-572-004

Bell & Gossett Pump Shaft
52-329-572-004

Bell & Gossett pump shaft 52-329-573-002

Bell & Gossett Pump Shaft
52-329-573-002

A pump shaft carries the impeller and turns with the motor, so it takes the full load of the pump. When a shaft wears at the seal or sleeve area, leaks and vibration follow, and the pump loses performance. A worn Bell & Gossett Pump Shaft should be replaced with the matching genuine part, not repaired with a generic substitute, because the fit at the impeller, bearings and seal must stay exact. The part numbers on this page are the numbers Bell & Gossett assigned to each shaft, so you can match the shaft you remove with the shaft you order.

KBS Industries stocks genuine Bell & Gossett Pump Shafts for the pump models our customers run every day. Each Bell & Gossett Pump Shaft on this page is listed by its part number, so you can check it against the shaft in your pump or against your pump nameplate before you order. If the number on your old shaft is worn away, or if you are not sure which of the three shafts fits your pump, send us the pump model and serial number and we will help you confirm the match. We ship Bell & Gossett parts across the United States and support the pumps we sell.

Signs a Bell & Gossett Pump Shaft Needs Replacing

Vibration, a leak at the seal, or a shaft that no longer runs true are the usual signs that a Bell & Gossett Pump Shaft is worn. Scoring or grooves where the seal rides, a loose impeller fit, or pitting from corrosion all mean the shaft surface can no longer seal or support the impeller correctly. Replacing the shaft at this stage protects the new seal and bearings, because a worn shaft will damage new parts quickly. If your pump has started to vibrate or leak, check the shaft before you order seals alone.

How to Choose the Right Bell & Gossett Pump Shafts

Start with the part number on the shaft you are replacing. Bell & Gossett Pump Shafts differ in length, diameter and keyway, so a shaft that looks right can still be the wrong fit. Compare the number, measure the shaft at the bearing and seal areas, and check the impeller fit before you order. If the shaft ran with a damaged sleeve or seal, inspect those parts too, because a scored shaft often means the sleeve and seal need attention as well.

  • Match the part number on the old shaft exactly.
  • Measure the shaft diameter at the bearings and at the seal.
  • Check the impeller bore and keyway for wear.
  • Replace a scored shaft sleeve at the same time.
  • Ask KBS Industries to confirm the fit if the number is unreadable.

Bell & Gossett Pump Shafts: What Fits Your Pump

Only three Bell & Gossett Pump Shafts are listed on this page, because Bell & Gossett built these shafts for specific pump frames, and each frame takes its own shaft. The part number tells you which frame the shaft belongs to, so start there and do not guess from length alone. Two shafts can share a diameter and still differ at the impeller end, the keyway, or the seal area, and any of those differences will stop the pump from running true. If you have the pump nameplate, send us the model and serial number with your enquiry. We can then check the shaft against the factory parts list for that pump and confirm the match before you order. When a shaft is replaced, it is good practice to fit a new sleeve and seal at the same time, because the old sleeve and seal have run on the worn shaft and may not seat correctly on the new one. A fresh shaft with a new sleeve and seal gives the pump a clean start and protects the bearings from the leaks and vibration that a worn shaft causes. KBS Industries can supply the matching Bell & Gossett seals, sleeves, bearings and glands for the same pump, so the whole rebuild can be ordered together and fitted in one visit.

Bell & Gossett Pump Shafts at KBS Industries

KBS Industries supplies Bell & Gossett Pump Shafts with the part numbers shown on this page, and our team can help you find the right shaft for your pump. Call or email us with your pump model, serial number or the part number from your old shaft, and we will confirm the match before you order. We also stock Bell & Gossett seals, bearings, sleeves and glands, so a full rebuild can be ordered in one place. Contact KBS Industries today to check stock and get your pump back in service.

Browse More Bell & Gossett Parts

You can find the full range on our Bell & Gossett page, with Bell & Gossett Mechanical Seals – HSC Pump, Bell & Gossett Mechanical Seals – End Suction Pump, Bell & Gossett Seal Replacement Kits, Bell & Gossett Bearings, Bell & Gossett Shaft Sleeves, Bell & Gossett Glands and Bell & Gossett Gaskets & Accessories. For pump curves, manuals and factory guidance, see the manufacturer’s Bell & Gossett website.