Peerless Pump Packing Rings
Peerless Pump Packing Rings: Browse our Peerless Pump Packing Rings below. Every part is a genuine Peerless spare, shown with its part number, so you can find the packing ring you need for your Peerless pump. The list covers 3 genuine Peerless Pump Packing Rings. Contact KBS Industries if you need help finding the right part.
Packing Ring
269249401
Packing Ring
96690125
Packing Ring
96694512
Each part on this page is a genuine Peerless pump part, listed with its Peerless part number. If you are matching a part from a pump nameplate, a service report or an old packing ring, start with the number on this page and compare it with the number on your pump. A matching number is the surest way to order the right Peerless Pump Packing Rings part.
The Peerless Pump Packing Rings on this page are the rings that pack the stuffing box of a Peerless pump, sealing the shaft where it leaves the casing. Packing rings are cut to length, fitted one at a time with their joints staggered, and compressed by the gland so they press against the shaft and the box wall. The three rings on this page, part numbers 269249401, 96690125 and 96694512, cover the packing ring sizes KBS Industries supplies for Peerless pumps. If your pump uses packing rather than a mechanical seal, these rings are the parts that keep the seal tight.
Browse the full Peerless Pump Parts range, and see the other Peerless Pump categories: Peerless Pump Mechanical Seals, Peerless Pump Bearings, Peerless Pump Lantern Rings, Peerless Pump Packing Rings, Peerless Pump Glands, Peerless Pump Shaft Sleeves, Peerless Pump Casing Rings and Peerless Pump O-Rings.
How to Choose the Right Peerless Pump Packing Rings
Match the part number first. Peerless part numbers are the fastest check: if the number on your old packing ring, your pump manual or your last order matches one on this page, you have the right part. Do not rely on size alone, because rings that look alike can differ in cross-section and material.
Check the stuffing box before you order. The packing ring must fit the box: too thick and it will not go in, too thin and it will not seal. Measure the box bore and the shaft or sleeve diameter, and work out the cross-section from the difference. Note how many rings the box holds and whether a lantern ring sits between them, so you order the right number of rings.
Inspect the old packing. Packing that is hard, glazed or crumbling has lost its seal, and packing that has worn a groove into the shaft sleeve has done its damage. Check the sleeve for scoring before you fit new rings, because a scored sleeve will wear the new packing out fast. Fit the new rings with their joints staggered around the shaft, never lined up.
Mind the parts around the packing. The packing rings work with the lantern ring between them and the gland that compresses them, so a repack is the right time to check both. If you are repacking a Peerless pump, see our Peerless Pump Lantern Rings page for the lantern rings, and our Peerless Pump Glands page for the gland parts. Changing the packing, the lantern ring and the gland parts together gives the seal the best chance of lasting.
For the manufacturer’s own information, see Peerless Pump. Peerless Pump Company builds the pumps these parts fit, including fire, industrial, municipal and process pumps, and their parts and service pages can help you confirm a pump model and its service parts. The Peerless Pump Packing Rings on this page are genuine Peerless spares for those pumps.
Storing and Fitting Peerless Pump Packing Rings
Store spare Peerless Pump Packing Rings flat in a dry place, away from heat and sunlight, and keep each ring in its own bag or box with its part number on the label. Packing that dries out or gets dirty will not seal, so handle it with clean hands and keep it away from grit. Check a stored ring before you fit it, and throw away any ring that is hard, cracked or contaminated.
Fit Peerless Pump Packing Rings one at a time, with the joints staggered. Cut each ring to length so its ends meet without a gap and without overlap, then push it into the box and seat it with the gland follower or a packing tool. Put the lantern ring in its place between the packing rings, with its holes facing the sealing liquid connection, and add the remaining rings in the order you noted when you took the box apart.
Tighten the gland evenly and a little at a time. The gland should compress the packing just enough to stop the leak, and no more: an overtightened gland will overheat the shaft and wear the packing out. Peerless Pump Packing Rings should be snug, not crushed, and the gland nuts should be tightened evenly so the gland stays square to the shaft.
After fitting, run the pump and watch the seal. A little leakage at first is normal while the packing beds in, but a steady stream or a hot stuffing box means something is wrong: stop the pump, check that the lantern ring holes line up with the liquid connection, and ease or tighten the gland evenly. Write the part number and the fitting date on the pump file so the next service starts from the right Peerless Pump Packing Rings part.
When to Replace Peerless Pump Packing Rings
Replace the packing whenever the stuffing box leaks more than a drip or the gland has run out of take-up. Packing wears with use, and once it is hard or glazed it cannot seal however tight the gland is. If the gland nuts are at the end of their travel and the box still leaks, the packing is worn out and it is time to repack.
Watch for the signs of worn packing. A stuffing box that runs hot, packing that needs constant tightening, or sealing liquid that no longer reaches the shaft can all point to packing that has had its day. Peerless Pump Packing Rings that are worn thin let the shaft move in the box, which scores the sleeve and shortens the life of the next set of rings.
Keep spares on the shelf. The three Peerless Pump Packing Rings on this page cover the rings KBS Industries supplies for Peerless pumps, so keep the number for your pump on file and order a spare set before the next planned repack. A spare set on the shelf means a repack is never held up waiting for parts, and the pump is back in service on schedule.
Ordering from KBS Industries
KBS Industries supplies the Peerless Pump Packing Rings on this page without prices or a cart: ask the team for a quote and they will confirm availability and delivery before you order. Keep the part number with the pump’s records so the next service goes faster. A note on the pump file with the packing ring number and the date it was fitted means the next person to open the pump orders the same ring without guessing.
