Tuesday, November 17, 2026

Peerless Pump O-Rings

Peerless Pump O-Rings: Browse our Peerless Pump O-Rings below. Every part is a genuine Peerless spare, shown with its part number, so you can find the O-ring you need for your Peerless pump. The list covers 1 genuine Peerless Pump O-Ring. Contact KBS Industries if you need help finding the right part.

Peerless pump O-ring 96675478 — Peerless Pump O-Rings

Peerless Pump O-Ring
96675478

Each part on this page is a genuine Peerless pump part, listed with its Peerless part number. If you are matching a part from a pump nameplate, a service report or an old seal kit, start with the number on this page and compare it with the number on your pump. A matching number is the surest way to order the right Peerless Pump O-Ring.

The Peerless Pump O-Ring listed here, part number 96675478, is the sealing ring used in Peerless pump assemblies. O-rings sit between mating faces and keep pumped liquid inside the pump, so a worn or flattened ring is a common cause of a slow leak at a joint. Replacing the ring when a pump is opened for service is a small job that can save a second strip-down later. If you are unsure which ring your pump takes, send KBS Industries the pump model and the part number and the team will check it for you. Peerless Pump O-Rings are worth replacing at every service, not only when they leak.

Browse the full Peerless Pump Parts range, and see the other Peerless Pump categories: Peerless Pump Mechanical Seals, Peerless Pump Bearings, Peerless Pump Lantern Rings, Peerless Pump Packing Rings, Peerless Pump Glands, Peerless Pump Shaft Sleeves, Peerless Pump Casing Rings and Peerless Pump O-Rings.

How to Choose the Right Peerless Pump O-Rings

Match the part number first. Peerless part numbers are the fastest check: if the number on your old O-ring, your pump manual or your last order matches 96675478, you have the right part. Do not rely on size alone, because rings that look alike can differ in thickness and material.

Check where the ring sits. O-rings seal joints in the pump, including the seal flange and the shaft sleeve, so note which joint you are working on before you order. If the ring comes out of a seal kit, check the kit number as well. The AE minor repair kits on our Peerless Pump Mechanical Seals page, for example, include seal flange O-rings as part of the kit. Peerless Pump O-Rings are sold by part number, so the number matters more than the size.

Inspect the old ring. A good O-ring is round and springy. If yours is flat, cracked, swollen or hard, replace it and look for the cause. Heat, the wrong fluid or a pinched fit can all shorten a ring’s life. Fit the new ring clean and dry, without stretching it over sharp edges.

Ask KBS Industries if you are not sure. Tell the team the pump model, the part number and where the ring fits, and they will confirm the part before you order. Contact KBS Industries for help with any Peerless Pump O-Rings part.

For the manufacturer’s own information, see Peerless Pump. Peerless Pump Company builds the pumps these parts fit, including fire, industrial, municipal and process pumps, and its parts and service pages cover the pump lines the Peerless Pump O-Rings on this page support. When you match a part number here with a Peerless pump model there, you can be confident the part belongs to that pump family.

Storing and Fitting Peerless Pump O-Rings

Store spare Peerless Pump O-Rings in a cool, dark, dry place, away from sunlight, heat and electric motors, which give off ozone that can age rubber. Keep each ring in its bag or box until you need it, and do not hang rings on hooks or nails, which can stretch them out of shape. A ring that has been sitting on a shelf for years may have gone hard, so check it before you fit it: if it feels stiff or has taken a flat set, use a fresh one. Write the fitting date on the bag so the next service knows how old the spare is.

When you fit Peerless Pump O-Rings, clean the groove first and check it and the mating faces for nicks or burrs that could cut the new ring. Seat the ring evenly without twisting it, and do not stretch it more than you must to get it over the part. A light smear of a lubricant that suits the pumped liquid can help the ring slide into place, but only use one the pump manual allows. When the joint is closed, check that the ring has not been pinched.

If the part number has been lost, measure the old ring before you throw it away. Peerless Pump O-Rings are ordered by part number, so the surest route is to match the number on your pump manual or your last order. If you only have the old ring, measure its inside diameter and its thickness with calipers and note the groove it came from, then ask KBS Industries to match those measurements to the right Peerless part. Do not guess from a worn ring alone, because a ring that has been in service may have swollen or taken a set.

After fitting Peerless Pump O-Rings, run the pump and check the joint for weeping before the pump goes back into full service. A new ring sometimes needs the joint to be tightened evenly in stages, so work around the bolts in turn rather than tightening one side fully first. If the joint still weeps with a new ring in place, look for a scored groove, a bent flange or the wrong ring before you tighten further, because over-tightening can damage the new ring and the joint faces.

Ordering from KBS Industries

KBS Industries supplies the Peerless Pump O-Rings on this page without prices or a cart: ask the team for a quote and they will confirm availability and delivery for part number 96675478 before you order. Keep the part number with the pump’s records so the next service goes faster. A note on the pump file with the O-ring number, the date it was fitted and the joint it seals means the next person to open the pump orders the same ring without guessing.