Bell & Gossett Gaskets & Accessories
Bell & Gossett Gaskets: browse our Bell & Gossett Gaskets below. Every gasket listed here is a genuine Bell & Gossett spare, shown with its part number, so you can find the gasket you need for your Bell & Gossett pump. Contact KBS Industries if you need help finding the right part.
Bell & Gossett Gasket
P04080
Bell & Gossett Gasket
P04890
Bell & Gossett Gasket
P48690
Bell & Gossett Gasket
P5001250
Bell & Gossett Gasket
P5001274
Bell & Gossett Gasket
P57410
Bell & Gossett Gasket
P57700
Bell & Gossett Gasket
P75201
Bell & Gossett Gasket
P80734
Bell & Gossett Gasket
P80752
Bell & Gossett Gasket
P80765
Bell & Gossett Gasket
P80767
Bell & Gossett Gasket
P85077
Bell & Gossett Water Slinger
P53550
Bell & Gossett Water Slinger
P77320
Bell & Gossett Water Slinger
P81946
Bell & Gossett Throttle Bushing
P71378
Bell & Gossett Shaft Collar, VSC/VSCS, 2.625 in.
P90282
A gasket seals the joint between two pump parts, so water stays inside the pump and air stays out. On a Bell & Gossett pump, gaskets sit at the casing joints, the seal housing and the flange faces, and each one must match the joint it seals. A gasket that is flattened, torn or swollen by the pumped liquid will leak, and the leak often looks like a seal failure. The water slingers on this page throw water off the shaft before it can reach the bearings, while the throttle bushing and shaft collar set the running clearances inside the pump.
KBS Industries stocks genuine Bell & Gossett Gaskets for the pump models our customers run every day. Each Bell & Gossett Gasket on this page is listed by its part number, so you can check it against the gasket in your pump or against your pump nameplate before you order. If the number on your old gasket is worn away, or if you are not sure which gasket fits your pump, send us the pump model and serial number and we will help you confirm the match. We ship Bell & Gossett parts across the United States and support the pumps we sell.
Signs a Bell & Gossett Gasket Needs Replacing
A steady drip at a casing joint, a damp flange face, or a gasket that has gone hard and brittle are the usual signs that a Bell & Gossett Gasket is worn. Gaskets also fail when they are squeezed too hard, when the joint faces are scored, or when the pumped liquid attacks the gasket material. Replacing the gasket at this stage protects the seal and bearings, because a leaking joint lets air into the pump and water onto parts that must stay dry. If your pump has started to drip at a joint, check the gasket before you order seals alone.
How to Choose the Right Bell & Gossett Gaskets
Start with the part number on the gasket you are replacing. Bell & Gossett Gaskets differ in size, thickness and shape, so a gasket that looks right can still be the wrong fit. Compare the number, check the gasket against the joint face, and measure the bore before you order. If the joint ran with a damaged gasket, clean and inspect the faces too, because a scored face will damage a new gasket quickly.
- Match the part number on the old gasket exactly.
- Check the gasket shape against the joint face.
- Measure the bore and thickness.
- Replace slingers and collars that show wear at the same time.
- Ask KBS Industries to confirm the fit if the number is unreadable.
Bell & Gossett Gaskets: What Fits Your Pump
Eighteen Bell & Gossett Gaskets and accessories are listed on this page, covering the joints, slingers, bushing and collar that Bell & Gossett built for these pumps. The part number tells you which pump and joint the part belongs to, so start there and do not guess from size alone. Two gaskets can share a bore and still differ in thickness or bolt pattern, and any of those differences will stop the joint from sealing correctly. If you have the pump nameplate, send us the model and serial number with your enquiry. We can then check the part against the factory parts list for that pump and confirm the match before you order.
When a gasket is replaced, it is good practice to fit new slingers and check the throttle bushing at the same time, because these small parts protect the bearings and set the clearances that keep the pump running true. A fresh gasket with clean joint faces gives the pump a tight seal and keeps water away from the bearings. KBS Industries can supply the matching Bell & Gossett seals, sleeves, bearings and shafts for the same pump, so the whole rebuild can be ordered together and fitted in one visit.
Bell & Gossett Gaskets at KBS Industries
KBS Industries supplies Bell & Gossett Gaskets with the part numbers shown on this page, and our team can help you find the right gasket for your pump. Call or email us with your pump model, serial number or the part number from your old gasket, and we will confirm the match before you order. We also stock Bell & Gossett seals, bearings, sleeves and shafts, so a full rebuild can be ordered in one place. Contact KBS Industries today to check stock of Bell & Gossett Gaskets and get your pump back in service.
Ordering Bell & Gossett Gaskets from KBS Industries is simple. Find the part number on this page, then call or email us with the number and your pump model. We will confirm the gasket fits your pump, check our stock, and give you a delivery time. If you are rebuilding a pump, we can add the matching seal, sleeve and bearings to the same order, so everything arrives together and the pump can be rebuilt in one visit. Our team works with Bell & Gossett pumps every day, and we are glad to help you find the right part, even when the number on the old gasket is hard to read.
Browse More Bell & Gossett Parts
You can find the full range on our Bell & Gossett page, with Bell & Gossett Mechanical Seals – HSC Pump, Bell & Gossett Mechanical Seals – End Suction Pump, Bell & Gossett Seal Replacement Kits, Bell & Gossett Bearings, Bell & Gossett Shaft Sleeves, Bell & Gossett Pump Shafts and Bell & Gossett Glands. For pump curves, manuals and factory guidance, see the manufacturer’s Bell & Gossett website.
