Peerless Pump Lantern Rings
Peerless Pump Lantern Rings: Browse our Peerless Pump Lantern Rings below. Every part is a genuine Peerless spare, shown with its part number, so you can find the lantern ring you need for your Peerless pump. The list covers 3 genuine Peerless Pump Lantern Rings. Contact KBS Industries if you need help finding the right part.
Lantern Ring
269249301
Lantern Ring
269249302
Lantern Ring
269249303
Each part on this page is a genuine Peerless pump part, listed with its Peerless part number. If you are matching a part from a pump nameplate, a service report or an old lantern ring, start with the number on this page and compare it with the number on your pump. A matching number is the surest way to order the right Peerless Pump Lantern Rings part.
The Peerless Pump Lantern Rings on this page are the rings that sit in the stuffing box of a packed Peerless pump. A lantern ring, sometimes called a seal cage, holds the packing in place and lets sealing liquid reach the shaft through its holes or grooves, so the packing stays wet and the shaft stays cool. The three rings on this page, part numbers 269249301, 269249302 and 269249303, cover the lantern ring sizes KBS Industries supplies for Peerless pumps. If your pump uses packing rather than a mechanical seal, the lantern ring is one of the parts to check at every repack.
Browse the full Peerless Pump Parts range, and see the other Peerless Pump categories: Peerless Pump Mechanical Seals, Peerless Pump Bearings, Peerless Pump Lantern Rings, Peerless Pump Packing Rings, Peerless Pump Glands, Peerless Pump Shaft Sleeves, Peerless Pump Casing Rings and Peerless Pump O-Rings.
How to Choose the Right Peerless Pump Lantern Rings
Match the part number first. Peerless part numbers are the fastest check: if the number on your old lantern ring, your pump manual or your last order matches one on this page, you have the right part. Do not rely on size alone, because rings that look alike can differ in bore, width and hole pattern.
Check where the ring sits. The lantern ring fits in the stuffing box between the packing rings, with its holes lined up with the sealing liquid connection, so note its position before you take the box apart. The ring must line up with the liquid inlet, or the packing will run dry and wear the shaft. Count the packing rings on each side of the lantern ring and put them back in the same order.
Inspect the old ring. A good lantern ring is round and free of cracks, with its holes clear and its faces flat. If yours is cracked, worn thin or blocked, replace it and check the packing and the shaft sleeve as well, because a damaged ring can score the sleeve. Fit the new ring with its holes facing the liquid connection.
Mind the packing around it. The lantern ring works with the packing rings on each side of it, so a repack is the right time to change a worn ring. If you are repacking a Peerless pump, see our Peerless Pump Packing Rings page for the packing rings, and our Peerless Pump Glands page for the gland that holds them in. Changing the ring, the packing and the gland parts together gives the seal the best chance of lasting.
For the manufacturer’s own information, see Peerless Pump. Peerless Pump Company builds the pumps these parts fit, including fire, industrial, municipal and process pumps, and their parts and service pages can help you confirm a pump model and its service parts. The Peerless Pump Lantern Rings on this page are genuine Peerless spares for those pumps.
Storing and Fitting Peerless Pump Lantern Rings
Store spare Peerless Pump Lantern Rings flat in a dry place, away from heat and sunlight, and keep each ring in its own bag or box with its part number on the label. A ring that is bent, dropped or left loose in a drawer can go out of round, and a ring that is out of round will not seal evenly in the stuffing box. Check a stored ring for cracks and flat spots before you fit it, and clean its holes so sealing liquid can pass through freely.
Fit Peerless Pump Lantern Rings with the packing rings in the right order. Take the old packing and lantern ring out, clean the stuffing box and the shaft sleeve, and check the sleeve for scoring before you put anything back. Slide the new lantern ring onto the shaft with its holes facing the sealing liquid connection, then add the packing rings on each side in the order you noted when you took the box apart.
Do not force a lantern ring into place. If the ring will not slide in easily, check that the stuffing box is clean and that you have the right part number for the pump. A ring that has to be hammered in is either the wrong size or damaged, and fitting it anyway will score the shaft sleeve and shorten the life of the packing. Peerless Pump Lantern Rings should sit flat and square in the box, with the holes lined up with the liquid inlet.
After fitting, run the pump and watch the seal. A little leakage at first is normal while the packing beds in, but a steady stream or a hot stuffing box means something is wrong: stop the pump, check that the lantern ring holes line up with the liquid connection, and check that the gland is tightened evenly. Write the part number and the fitting date on the pump file so the next service starts from the right Peerless Pump Lantern Rings part.
When to Replace Peerless Pump Lantern Rings
Replace a lantern ring whenever you repack the stuffing box and the old ring shows wear. A ring that is cracked, grooved or worn thin will not hold the packing square, and the packing will wear unevenly and leak. If the ring is still round, smooth and free of cracks, it can stay in service, but most service engineers change it with the packing because the part is cheap compared with the labour of opening the box again.
Watch for the signs of a failing lantern ring. Packing that wears out quickly, a stuffing box that runs hot, or sealing liquid that does not reach the packing can all point to a blocked or misaligned ring. Peerless Pump Lantern Rings with blocked holes starve the packing of liquid, so check the holes before you blame the packing. A ring that has gone out of round will also show as uneven leakage around the gland.
Keep a spare on the shelf. The three Peerless Pump Lantern Rings on this page cover the rings KBS Industries supplies for Peerless pumps, so keep the number for your pump on file and order a spare before the next planned repack. A spare ring on the shelf means a repack is never held up waiting for a part, and the pump is back in service on schedule.
Ordering from KBS Industries
KBS Industries supplies the Peerless Pump Lantern Rings on this page without prices or a cart: ask the team for a quote and they will confirm availability and delivery before you order. Keep the part number with the pump’s records so the next service goes faster. A note on the pump file with the lantern ring number and the date it was fitted means the next person to open the pump orders the same ring without guessing.
