Peerless Pump Glands
Peerless Pump Glands: Browse our Peerless Pump Glands below. Every part is a genuine Peerless spare, shown with its part number, so you can find the gland part you need for your Peerless pump. The list covers 4 genuine Peerless Pump Glands. Contact KBS Industries if you need help finding the right part.
Packing Gland Bolt Assembly
96679240
Packing Gland Bolt Assembly
96691703
Packing Gland Bolt Assembly
96703125
Packing Gland
96765204
Each part on this page is a genuine Peerless pump part, listed with its Peerless part number. If you are matching a part from a pump nameplate, a service report or an old gland part, start with the number on this page and compare it with the number on your pump. A matching number is the surest way to order the right Peerless Pump Glands part.
The Peerless Pump Glands on this page are the parts that hold the packing in the stuffing box of a Peerless pump. The packing gland presses the packing rings against the shaft, and the gland bolt assemblies — the swing bolts, nuts and washers that pull the gland down — let you tighten the packing evenly. The four parts on this page are three packing gland bolt assemblies, part numbers 96679240, 96691703 and 96703125, and one packing gland, part number 96765204. If your pump uses packing rather than a mechanical seal, these are the parts that keep the seal tight and adjustable.
Browse the full Peerless Pump Parts range, and see the other Peerless Pump categories: Peerless Pump Mechanical Seals, Peerless Pump Bearings, Peerless Pump Lantern Rings, Peerless Pump Packing Rings, Peerless Pump Glands, Peerless Pump Shaft Sleeves, Peerless Pump Casing Rings and Peerless Pump O-Rings.
How to Choose the Right Peerless Pump Glands
Match the part number first. Peerless part numbers are the fastest check: if the number on your old gland part, your pump manual or your last order matches one on this page, you have the right part. Do not rely on size alone, because gland parts that look alike can differ in thread, length and bolt pattern.
Check what the gland does on your pump. The packing gland sits over the stuffing box and is drawn down by its bolts to compress the packing. If the gland is cracked, bent or worn where it meets the packing, it will not press evenly and the box will leak. If the bolt assembly is stripped, bent or missing its nuts, the gland cannot be tightened at all. Check both the gland and its bolts before you order.
Inspect the old gland parts. A good gland is flat where it meets the packing and square to the shaft, with its bolt holes clean and its threads sound. A gland that has been overtightened can be bowed or cracked, and bolts that have been forced can have stripped threads. Replace any part that is damaged, and check the packing and the shaft sleeve as well, because a bad gland can score the sleeve.
Mind the packing the gland compresses. The gland works with the packing rings and the lantern ring in the stuffing box, so a repack is the right time to check the gland parts. If you are repacking a Peerless pump, see our Peerless Pump Packing Rings page for the packing rings, and our Peerless Pump Lantern Rings page for the lantern rings. Changing the gland parts with the packing gives the seal the best chance of lasting.
For the manufacturer’s own information, see Peerless Pump. Peerless Pump Company builds the pumps these parts fit, including fire, industrial, municipal and process pumps, and their parts and service pages can help you confirm a pump model and its service parts. The Peerless Pump Glands on this page are genuine Peerless spares for those pumps.
Storing and Fitting Peerless Pump Glands
Store spare Peerless Pump Glands in a dry place, away from damp and grit, and keep each part in its own bag or box with its part number on the label. Gland bolts and nuts can rust if they are left loose in a damp store, and a rusted bolt can seize in the gland. Check a stored gland for cracks and a stored bolt for straightness and clean threads before you fit them.
Fit Peerless Pump Glands with the packing rings in the right order. Take the old packing out, clean the stuffing box and the shaft sleeve, and check the sleeve for scoring before you put anything back. Slide the new gland over the shaft, fit the packing rings and the lantern ring in their places, then draw the gland down with its bolt assemblies, tightening the nuts a little at a time and evenly on both sides so the gland stays square.
Tighten the gland evenly and a little at a time. The gland should compress the packing just enough to stop the leak, and no more: an overtightened gland will overheat the shaft and wear the packing out. Peerless Pump Glands should be snug, not forced, and the nuts should be tightened evenly so the gland stays square to the shaft and the packing wears evenly.
After fitting, run the pump and watch the seal. A little leakage at first is normal while the packing beds in, but a steady stream or a hot stuffing box means something is wrong: stop the pump, check that the gland is square and the nuts are even, and check that the lantern ring holes line up with the liquid connection. Write the part number and the fitting date on the pump file so the next service starts from the right Peerless Pump Glands part.
When to Replace Peerless Pump Glands
Replace the gland parts whenever the stuffing box cannot be sealed by tightening. If the gland nuts are at the end of their travel and the box still leaks, the packing is worn out, but if the gland itself is cracked, bowed or stripped, tightening will not help and the gland part must be replaced. A gland that rocks on the shaft or a bolt that will not hold its nut are both signs that the part has had its day.
Watch for the signs of a failing gland. Packing that wears out quickly, a stuffing box that runs hot, or a gland that has to be tightened again and again can all point to a gland that no longer presses evenly. Peerless Pump Glands that are worn or bent let the packing move in the box, which scores the sleeve and shortens the life of the next set of rings.
Keep spares on the shelf. The four Peerless Pump Glands on this page cover the gland parts KBS Industries supplies for Peerless pumps, so keep the number for your pump on file and order a spare before the next planned repack. A spare gland part on the shelf means a repack is never held up waiting for a part, and the pump is back in service on schedule.
Ordering from KBS Industries
KBS Industries supplies the Peerless Pump Glands on this page without prices or a cart: ask the team for a quote and they will confirm availability and delivery before you order. Keep the part number with the pump’s records so the next service goes faster. A note on the pump file with the gland part number and the date it was fitted means the next person to open the pump orders the same part without guessing.
