A-C Pump Casing Gaskets
A-C Pump Casing Gaskets: this page lists the 1 genuine A-C Pump casing gasket that KBS Industries carries for A-C (Allis Chalmers) pumps, shown with its part number below.
A casing gasket sits between the two halves of the pump casing and seals the joint so the pump holds pressure without leaking. When the casing is opened for service, the old gasket should be replaced rather than reused, because a flattened or torn gasket will not reseal.
Use the part number below to match the gasket to your pump before you order, and contact KBS Industries if you need help finding the right part. For the full A-C Pump range, start from our A-C Pump hub page.
A-C Pump Casing Gasket
52-431-816-104
Casing gasket for A-C pumps. It seals the joint between the casing halves so the pump holds pressure without leaking at the casing split.
What Are A-C Pump Casing Gaskets?
A-C Pump Casing Gaskets are flat sealing rings that fit between the casing halves of an A-C pump. The casing holds the impeller and the pumped liquid, so the joint between its halves must stay sealed under pressure.
The gasket fills the small gaps between the machined casing faces and stops liquid from escaping at the split line. Over time, heat, pressure and the liquid being pumped can compress or harden a gasket, and once a casing has been opened the old gasket rarely seals again.
That is why a fresh A-C Pump Casing Gasket belongs in every casing service. The part number is the surest way to match a gasket: casing sizes differ from one pump model to another, and a gasket that looks close can still be the wrong size.
Check the part number on the old gasket or on the pump nameplate, then match it to the number listed on this page. KBS Industries supplies genuine A-C parts made to the original size and material, so the gasket seats the way the pump maker intended. If your pump also needs other parts, see our A-C Pump Packing Rings, A-C Pump Lantern Rings, A-C Pump Shaft Sleeves and A-C Pump Mechanical Seals pages.
How to Choose A-C Pump Casing Gaskets
- Match the part number to your pump model before you order. The number on this page, 52-431-816-104, is the only casing gasket listed here.
- Check the casing split line for damage before fitting a new gasket. A scored or corroded face can leak even with a new gasket.
- Fit the gasket dry and clean. Wipe both casing faces clean and keep the gasket flat while the casing halves are brought together.
- Tighten the casing bolts evenly in a cross pattern so the gasket is compressed the same way all round.
- Replace the gasket every time the casing is opened. A used gasket has already taken a set and will not reseal well.
- Keep a spare gasket on site. Casing gaskets are small, low cost parts, and having one ready avoids downtime.
- Not sure which part fits your pump? Email sales@kbsindustries.com with your pump model and part number.
Order A-C Pump Casing Gaskets from KBS Industries
To order A-C Pump Casing Gaskets, email sales@kbsindustries.com with your pump model and the part number 52-431-816-104, or start from our A-C Pump hub.
For related A-C parts, see A-C Pump Mechanical Seals, A-C Pump Replacement Seal Kits, A-C Pump Minor Repair Kits, A-C Pump Lantern Rings, A-C Pump Shaft Sleeves and A-C Pump Packing Rings. A-C Pump is a Xylem brand — see the Xylem site for more on the brand. KBS Industries supplies genuine A-C Pump parts for Allis Chalmers pumps, and we can help you match the right part to your pump.
