Thursday, November 19, 2026

Eaton Freedom Series Components

Eaton Freedom Series Components: this page lists the 29 genuine Eaton parts that KBS Industries carries for Eaton Freedom series electric fire pump controllers, shown with their Eaton part numbers below.

These Eaton Freedom Series Components are the parts that wear, fail or need replacing when Freedom series controllers are serviced. They cover the contact kits and coils that switch the pump motor, the auxiliary contacts that signal the controller, and the contactors themselves. Because contactor coils are wound for a particular supply voltage, most parts on this page are listed by voltage, so the right coil can be matched to the controller’s supply.

Use the Eaton part number below to match the component to your controller before you order, and check the voltage variant carefully: a coil wound for one voltage will not work correctly on another. For the full Eaton fire pump range, start from our Eaton Fire Pump Control Spares hub page, and for the components shared across Eaton electric controllers, see Eaton Electric Common Components. For the A200 series parts, see Eaton A200 Series Components.

All Voltages

DescriptionEaton part no.DescriptionEaton part no.
Size 2 (set of 3)6-65-8Size 3 (set of 3)6-43-6
Size 4 (set of 3)6-26-2Size 5 (set of 3)6-45-2

Contactor coil

Contactor coil — no picture available

208 Volt

DescriptionEaton part no.DescriptionEaton part no.
Size 1 & 29-2703-9Size 39-2756-5
Size 4 & 59-1891-13

240Volt

DescriptionEaton part no.DescriptionEaton part no.
Size 1 & 29-2703-2Size 39-2756-2
Size 4 & 59-1891-2

380 Volt – 50HZ

DescriptionEaton part no.DescriptionEaton part no.
Size 1 & 29-2703-8Size 39-2756-12
Size 4 & 59-1891-14

415 Volt – 50HZ

DescriptionEaton part no.DescriptionEaton part no.
Size 1 & 29-2703-8Size 39-2756-8
Size 4 & 59-1891-21

480 Volt

DescriptionEaton part no.DescriptionEaton part no.
Size 1 & 29-2703-3Size 39-2756-3
Size 4 & 59-1891-3

600 Volt

DescriptionEaton part no.DescriptionEaton part no.
Size 1 & 29-2703-4Size 39-2756-4
Size 4 & 59-1891-4

Auxiliary contact

Auxiliary contact — no picture available

Form C (for Freedom Contactor)

DescriptionEaton part no.DescriptionEaton part no.
Size 1 & 2C320KGS3Size 3C320KGS22
Size 4 & 5C320KGS42

Contactor

Contactor — no picture available

All Voltages

DescriptionEaton part no.DescriptionEaton part no.
Size 2CN15GN3ASize 3CN15KN3A
Size 4CN15NN3ASize 5CN15SN3A

What Are Eaton Freedom Series Components?

Eaton Freedom Series Components are the genuine Eaton replacement parts for Freedom series electric fire pump controllers. The contactor is the heavy duty switch that starts and stops the fire pump motor, and the contact kit is the set of contacts inside it that carry the motor current. Over time those contacts pit and wear from switching the motor load, and a new contact kit restores the contactor without replacing the whole unit.

The contactor coil among these Eaton Freedom Series Components is the electromagnet that closes the contactor when the controller calls for the pump to run. Coils are made for a specific supply voltage and frequency, which is why the coil section of this page is divided by voltage, from 208 volts to 600 volts, including 50 hertz versions where the catalog lists them. Fitting a coil of the wrong voltage can leave the contactor chattering, failing to close, or burning out.

Auxiliary contacts fit alongside the main contactor and give the controller a signal that the contactor has closed, or switch a separate low current circuit. The Form C auxiliary contacts among these Eaton Freedom Series Components are made for the Freedom contactor used in Freedom series controllers. They are small parts, but a failed auxiliary contact can stop a controller from proving the pump has started.

Every part on this page is a genuine Eaton part, supplied with its Eaton part number. Eaton builds its fire pump controllers to the standards fire protection systems depend on, and using the maker’s own components keeps the controller’s ratings and approvals intact. For the manufacturer’s own fire pump control range, see Eaton fire pump controls.

How to Choose Eaton Freedom Series Components

  • Match the Eaton part number to your controller model before you order. The numbers on this page are the surest way to identify the right Eaton Freedom Series Components.
  • Check the contactor size before ordering a contact kit or a coil. Sizes 1 to 5 use different parts, and a kit for one size will not fit another.
  • Match the coil voltage and frequency to the controller supply. A 208 volt coil will not suit a 480 volt controller, and 50 hertz and 60 hertz coils are not interchangeable.
  • Note that some coil sizes are grouped. Sizes 1 and 2 share a coil, and sizes 4 and 5 share a coil, so check the size range on the part you order.
  • Choose the auxiliary contact arrangement your controller needs. The Form C contacts listed here are made for the Freedom contactor, with a different part for each contactor size range.
  • Check whether the contact kit is a set of three. All of the Freedom contact kits on this page are sets of three contacts, one for each pole.
  • Not sure which part fits your controller? Email sales@kbsindustries.com with the controller model, the contactor size and the supply voltage, and the part you need.

Order Eaton Freedom Series Components from KBS Industries

To order Eaton Freedom Series Components, email sales@kbsindustries.com with the Eaton part numbers you need and the quantity for each. KBS Industries will confirm availability and delivery for your order.

For related Eaton parts, see Eaton Electric Common Components and Eaton A200 Series Components, and for the whole fire pump control range, return to the Eaton Fire Pump Control Spares hub page.