Eaton FD120 Components
Eaton FD120 Components: this page lists the 33 genuine Eaton parts that KBS Industries carries for Eaton FD120 diesel fire pump controllers, shown with their Eaton part numbers below. Three further rows show parts that have been superseded, with their replacements listed below the old numbers.
These Eaton FD120 Components are the parts that wear, fail or need replacing when FD120 controllers are serviced. They cover the battery charger, pushbuttons and membranes, the main display board, the power I/O board and the engine board, the pressure sensor, and the drain valve, isolating diode pack and buzzer.
Use the Eaton part number below to match the component to your controller before you order, and check the part carefully: some descriptions look alike but carry different part numbers, and three boards on this page have been superseded by later parts. For the full Eaton fire pump range, start from our Eaton Fire Pump Control Spares hub page. For the components shared across Eaton electric controllers, see Eaton Electric Common Components, and for the other electric ranges, see Eaton A200 Series Components, Eaton Freedom Series Components, Eaton XT Series Components, Eaton Transfer Switch Components, Eaton LMR Plus Components, Eaton EPCT Fire Components and Eaton EPCT Fire Transfer Switch Components.
| Description | Eaton part no. | Description | Eaton part no. |
|---|---|---|---|
| Retrofit Charger (FD100/FD110 Controllers) | 4A55541G01 | Battery Charger – 100 / 240VAC – 12 / 24VDC | 4A55505H01 |
| Battery Charger Serial Cable | 4A55765H05 |
Pushbutton
| Description | Eaton part no. | Description | Eaton part no. |
|---|---|---|---|
| Crank #1 or #2 and Contact Block | 10250T101 + 10250T53 | Crank #1 or #2 and Contact Block | M22-D-S-K10 |
| Stop and Contact Block | 10250T112 + 10250T53 | Stop and Contact Block | M22-DH-R-K10 |
| DC Failure Alarm – 12VDC – Light and Lens | 10250T204N + 10250TC1N | DC Failure Alarm – 12VDC – Light and Lens | M22-L-R-R |
| 3 Position Switch & Contact Block (Man-Off-Auto) | 10250T1323 + 10250T2 | 3 Position Switch & Contact Block (Man-Off-Auto) | M22-WRK3-K20 |
Membrane
| Description | Eaton part no. | Description | Eaton part no. |
|---|---|---|---|
| Membrane – English | CE16196H01 | Membrane – French | CE16196H02 |
| Membrane – Spanish | CE19196H05 |
Main display board
| Description | Eaton part no. | Description | Eaton part no. |
|---|---|---|---|
| Main Display Board | 4A55765H24 | Main Display Board – COM option | 4A55765H21 |
| Data Cable – Logic Board to Input / Output Board | 4A55723H01 | Power Cable – Logic Board to Input / Output Board | 4A55723H02 |
| Main Display Board | 4A55765H11 (Obsolete) Latest: 4A55765H24 |
Power i/o board

| Description | Eaton part no. | Description | Eaton part no. |
|---|---|---|---|
| Power I/O Board | 4A55765H22 | Engine Run Relay – 24Vdc – (600V contact rating) | 4A55517H01 |
| Auxilliary Relay Board (Includes two PCB Output Relay) | 99-5836-01 | Ribbon Cable (P7) – Relay Board to Controller | 5D15229H05 |
| Power I/O Board | 4A55765H02 (Obsolete) Latest: 4A55765H22 |
Engine board

| Description | Eaton part no. | Description | Eaton part no. |
|---|---|---|---|
| Engine Board | 4A55765H23 | Engine Board (Ribbon Cable) Engine Board to Power I/O Board | 4A55765H04 |
| Engine Board Relay – 24Vdc | 1432826-1 | Engine Board | 4A55765H03 (Obsolete) Latest: 4A55765H23 |
Pressure sensor
| Description | Eaton part no. | Description | Eaton part no. |
|---|---|---|---|
| Pressure Sensor 4-20mA | CE16518H01 |
Buzzer
| Description | Eaton part no. | Description | Eaton part no. |
|---|---|---|---|
| Panel Mount Buzzer – 24VDC, Continuous Output | MC-07-130-SR |
Isolating diode pack
| Description | Eaton part no. | Description | Eaton part no. |
|---|---|---|---|
| 15 Amps | 3A13987H15 |
Drain valve solenoid
Drain Valve 12-24 VDC
| Description | Eaton part no. | Description | Eaton part no. |
|---|---|---|---|
| 1/2″ Drain Valve Assemblies | CE16519G01 | 1/2″ Drain Valve Assemblies | CE16519H01 |
Miscellaneous
| Description | Eaton part no. | Description | Eaton part no. |
|---|---|---|---|
| Main Door Handle | 349P236G01 | Breakable Glass Cover Assembly for Man-Off-Auto | 47-51668 |
Pre-FM 2015 retrofit group
| Description | Eaton part no. | Description | Eaton part no. |
|---|---|---|---|
| Retrofit group | CE16777G01 |
What Are Eaton FD120 Components?
Eaton FD120 Components are the replacement parts for Eaton’s FD120 diesel fire pump controllers, the microprocessor-based panels used on diesel engine-driven fire pump installations. Each controller combines a main display board, a power I/O board and an engine board, with a battery charger keeping the engine batteries ready, pushbuttons for manual control, and a pressure sensor that starts the engine on demand. Because the FD120 is a widely installed controller, its spares cover the parts most often needed during servicing, from the boards and charger to the pushbuttons, membranes and drain valve solenoid.
In an Eaton FD120 Components installation, the controller reads system pressure through its 4-20mA pressure sensor and uses that signal to decide when to crank the engine. The main display board shows status and alarms, the power I/O board drives the outputs and the engine run relay, and the engine board manages the engine signals. The battery charger keeps the starting batteries charged, the isolating diode pack separates the battery circuits, and the panel-mount buzzer sounds when an alarm condition occurs.
Three of the Eaton FD120 Components boards on this page have been superseded. The main display board originally supplied as 4A55765H11 is now obsolete and its current replacement is 4A55765H24; the power I/O board 4A55765H02 is replaced by 4A55765H22; and the engine board 4A55765H03 is replaced by 4A55765H23. Each current board is also listed here as its own part. If your controller still carries one of the older boards, order the current number: it is the direct replacement and the number to use going forward. The obsolete numbers are kept on the page so that anyone matching an old parts list can find the right current part without guessing.
Every one of these Eaton FD120 Components is a genuine Eaton part, supplied with its Eaton part number. Genuine parts keep the controller’s ratings, connections and behaviour exactly as Eaton designed them, which matters in a fire pump application where the controller must start the engine first time, every time. For more background on Eaton’s fire pump range, see Eaton’s fire pump page.
How to Choose Eaton FD120 Components
Match the part to your controller before you order. The checks below cover the most common mistakes when ordering Eaton FD120 Components spares.
- When ordering Eaton FD120 Components, check the Eaton part number on the failed component or on your controller’s parts list — similar boards and sensors are not interchangeable.
- Match the pushbutton style: the 10250T operators and the M22 operators fit different mounting arrangements.
- For the three superseded boards, order the current numbers — 4A55765H24 for the main display board, 4A55765H22 for the power I/O board and 4A55765H23 for the engine board — not the obsolete numbers.
- Confirm whether your controller has the COM option before ordering a main display board — the standard board is 4A55765H24 and the COM option board is 4A55765H21.
- Order the input/output board by its full number: the power I/O board is 4A55765H22 and the auxiliary relay board is 99-5836-01.
- Check the drain valve voltage and mounting: the assemblies listed here are the 12-24 VDC versions, CE16519G01 and CE16519H01.
- If you are unsure which part fits your controller, email sales@kbsindustries.com with the controller model and the part number you need.
Order Eaton FD120 Components from KBS Industries
Order your Eaton FD120 Components from KBS Industries by emailing sales@kbsindustries.com with the Eaton part numbers you need and the quantity for each. We will confirm availability and pricing, and arrange delivery to your site. If a part you need is not listed here, tell us the number — we can often source other Eaton fire pump spares on request.
These Eaton FD120 Components sit alongside spares for the other Eaton fire pump controller ranges carried by KBS Industries. See our Eaton Fire Pump Control Spares hub page for the full list, and the neighbouring sections — Eaton EPCT Fire Transfer Switch Components, Eaton EPCT Fire Components, Eaton LMR Plus Components, Eaton XT Series Components, Eaton Transfer Switch Components, Eaton Freedom Series Components and Eaton A200 Series Components — for parts from the other controller families.

