Thursday, November 19, 2026

Eaton LMR Plus Components

Eaton LMR Plus Components: this page lists the 21 genuine Eaton parts that KBS Industries carries for Eaton LMR Plus electric fire pump controllers, shown with their Eaton part numbers below. One further row shows a part that has been superseded, with its replacement listed below the old number.

These Eaton LMR Plus Components are the parts that wear, fail or need replacing when LMR Plus controllers are serviced. They cover the pushbuttons, membranes and microprocessor assembly, the input and output boards, the relays and cables, the pressure sensor, and the drain valve, transformer and buzzer.

Use the Eaton part number below to match the component to your controller before you order, and check the part carefully: some descriptions look alike but carry different part numbers, and one pressure sensor on this page has been superseded by a later part. For the full Eaton fire pump range, start from our Eaton Fire Pump Control Spares hub page. For the components shared across Eaton electric controllers, see Eaton Electric Common Components, and for the other electric ranges, see Eaton A200 Series Components, Eaton Freedom Series Components, Eaton XT Series Components and Eaton Transfer Switch Components.

DescriptionEaton part no.DescriptionEaton part no.
Operator Green Start PB + 1 N.O. Contact Block10250T103 + 10250T53Operator Green Start PB + 1 N.O. Contact BlockM22-D-G-K10
Operator Red Stop PB + 1 N.O. Contact Block10250T112 + 10250T53Operator Red Stop PB + 1 N.O. Contact BlockM22-DH-R-K10

Membrane

Eaton fire pump membrane 99-5835-01
DescriptionEaton part no.DescriptionEaton part no.
Membrane – English99-5816-01

Membrane – foam controller

Membrane - foam controller — no picture available
DescriptionEaton part no.DescriptionEaton part no.
Membrane – English99-5817-01

Microprocessor assembly

Eaton fire pump logic board 99-5835-12
DescriptionEaton part no.DescriptionEaton part no.
Logic Controller Board99-5835-12Logic Controller Board – COM Option99-5835-02

Power i/o board

Power i/o board — no picture available
DescriptionEaton part no.DescriptionEaton part no.
Input / Output Board4A55149H02Input / Output Board99-5835-01

Optional relay board

Optional relay board — no picture available
DescriptionEaton part no.DescriptionEaton part no.
Auxilliary Relay Board (Includes two PCB Output Relays)99-5836-01

Data and communication cable

Data and communication cable — no picture available
DescriptionEaton part no.DescriptionEaton part no.
Data Cable – Logic Board to Input / Output Board4A55723H01Power Cable – Logic Board to Input / Output Board4A55723H02

Relay

Relay — no picture available
DescriptionEaton part no.DescriptionEaton part no.
PCB Output Relays3A18033H09Relay – 600V Rated4A55517H01

Pressure sensor

Pressure sensor — no picture available
DescriptionEaton part no.DescriptionEaton part no.
4-20mA Pressure SensorCE16518H014-20mA Pressure Sensor4A55678H01 (Obsolete)
Latest: CE16518H01

Drain valve solenoid

Drain valve solenoid — no picture available

Drain Valve 12-24VDC

DescriptionEaton part no.DescriptionEaton part no.
1/2″ Drain Valve AssembliesCE16519G03

Transformer

Transformer — no picture available
DescriptionEaton part no.DescriptionEaton part no.
Transformer – 380 / 480 / 600 Volt Primary4A55513H01

Cable assembly

Cable assembly — no picture available
DescriptionEaton part no.DescriptionEaton part no.
Cable Mechanism – SingleF1S03CCable Mechanism – DoubleF1S03CD

Buzzer

Buzzer — no picture available
DescriptionEaton part no.DescriptionEaton part no.
Panel Mount Buzzer – 24VDC, Continuous OutputMC-07-130-SR

What Are Eaton LMR Plus Components?

Eaton LMR Plus Components are the replacement parts for Eaton’s LMR Plus fire pump controllers, the microprocessor-based panels used on electric fire pump installations. Each controller combines a logic controller board, an input/output board, operator pushbuttons, a membrane keypad and a pressure sensor, all working together to start the pump on demand and keep it running until the system pressure is restored. Because the LMR Plus is a widely installed controller, its spares cover the parts most often needed during servicing, from the logic board and relay board to the drain valve solenoid and transformer.

In an Eaton LMR Plus Components installation, the controller reads system pressure through its 4-20mA pressure sensor and uses that signal to decide when to start and stop the pump. The logic controller board processes the signal, drives the outputs through the input/output board, and shows status and alarms on the membrane display. Pushbuttons give the operator manual start and stop control, while the auxiliary relay board adds extra output contacts for alarms and remote signals. Data and power cables link the boards, and the panel-mount buzzer sounds when an alarm condition occurs.

One part on this page has been superseded. The 4-20mA pressure sensor originally supplied as 4A55678H01 is now obsolete, and Eaton’s current replacement is CE16518H01, which is also listed here as the current part. If your controller still carries the older sensor, order CE16518H01: it is the direct replacement and the number to use going forward. The obsolete number is kept on the page so that anyone matching an old parts list or an existing installation can find the right current part without guessing.

Every one of these Eaton LMR Plus Components is a genuine Eaton part, supplied with its Eaton part number. Genuine parts keep the controller’s ratings, connections and behaviour exactly as Eaton designed them, which matters in a fire pump application where the controller must start the pump first time, every time. For more background on Eaton’s fire pump range, see Eaton’s fire pump page.

How to Choose Eaton LMR Plus Components

Match the part to your controller before you order. The checks below cover the most common mistakes when ordering Eaton LMR Plus Components spares.

  • Check the Eaton part number on the failed component or on your controller’s parts list — similar boards and sensors are not interchangeable.
  • Match the pushbutton style: the 10250T operators and the M22 operators fit different mounting arrangements.
  • Confirm whether your controller has the COM option before ordering a logic controller board — the standard board is 99-5835-12 and the COM option board is 99-5835-02.
  • Order the input/output board by its full number: 4A55149H02 and 99-5835-01 are different boards.
  • For the pressure sensor, order CE16518H01 — the older 4A55678H01 is obsolete and CE16518H01 is the current replacement.
  • Check the drain valve voltage: the assembly listed here is the 12-24VDC version, CE16519G03.
  • If you are unsure which part fits your controller, email sales@kbsindustries.com with the controller model and the part number you need.

Order Eaton LMR Plus Components from KBS Industries

Order your Eaton LMR Plus Components from KBS Industries by emailing sales@kbsindustries.com with the Eaton part numbers you need and the quantity for each. We will confirm availability and pricing, and arrange delivery to your site. If a part you need is not listed here, tell us the number — we can often source other Eaton fire pump spares on request.

These Eaton LMR Plus Components sit alongside spares for the other Eaton fire pump controller ranges carried by KBS Industries. See our Eaton Fire Pump Control Spares hub page for the full list, and the neighbouring sections — Eaton XT Series Components, Eaton Transfer Switch Components, Eaton Freedom Series Components and Eaton A200 Series Components — for parts from the other electric controller families.