Thursday, November 19, 2026

Eaton A200 Series Components

Eaton A200 Series Components: this page lists the 28 genuine Eaton parts that KBS Industries carries for Eaton A200 series electric fire pump controllers, shown with their Eaton part numbers below.

These Eaton A200 Series Components are the parts that wear, fail or need replacing when A200 series controllers are serviced. They cover the contact kits and coils that switch the pump motor, the auxiliary contacts that signal the controller, and the contactors themselves. Because contactor coils are wound for a particular supply voltage, most parts on this page are listed by voltage, so the right coil can be matched to the controller’s supply.

Use the Eaton part number below to match the component to your controller before you order, and check the voltage variant carefully: a coil wound for one voltage will not work correctly on another. For the full Eaton fire pump range, start from our Eaton Fire Pump Control Spares hub page, and for the components shared across Eaton electric controllers, see Eaton Electric Common Components.

All Voltages

DescriptionEaton part no.DescriptionEaton part no.
Size 3 (set of 3)626B187G13Size 4 (set of 3)5250C81G17
Size 5 (1-pole)477B477G05Size 6 (1-pole)2066A10G11

Contactor coil

Contactor coil — no picture available

208 Volt

DescriptionEaton part no.DescriptionEaton part no.
Size 45250C79G02Size 62050A12G09

240 Volt

DescriptionEaton part no.DescriptionEaton part no.
Size 45250C79G12Size 62050A12G10

380 Volt – 50 HZ

DescriptionEaton part no.DescriptionEaton part no.
Size 45250C79G07Size 62050A12G14

380 Volt – 60 HZ

DescriptionEaton part no.DescriptionEaton part no.
Size 3 “J” Style505C633G27Size 4 “K” Style5250C79G27
Size 52050A14G19Size 62050A12G19

415 Volt – 50HZ

DescriptionEaton part no.DescriptionEaton part no.
Size 52050A14G14Size 62050A12G14

415 Volt – 60HZ

DescriptionEaton part no.DescriptionEaton part no.
Size 52050A14G19Size 62050A12G19

480 Volt

DescriptionEaton part no.DescriptionEaton part no.
Size 45250C79G13Size 62050A12G15

600 Volt

DescriptionEaton part no.DescriptionEaton part no.
Size 45250C79G05Size 62050A12G17

Auxiliary contact

Auxiliary contact — no picture available

Form C (for model A201 Contactor)

DescriptionEaton part no.DescriptionEaton part no.
J11 – 1 N.O. & 1 N.C. Contact9084A17G01J20 – 2 N.O. Contacts9084A17G02

Contactor

Contactor — no picture available

All Voltages

DescriptionEaton part no.DescriptionEaton part no.
Size 35277C15G04Size 45250C85G02
Size 52045A40G01Size 6A201K6CX

What Are Eaton A200 Series Components?

Eaton A200 Series Components are the genuine Eaton replacement parts for A200 series electric fire pump controllers. The contactor is the heavy duty switch that starts and stops the fire pump motor, and the contact kit is the set of contacts inside it that carry the motor current. Over time those contacts pit and wear from switching the motor load, and a new contact kit restores the contactor without replacing the whole unit.

The contactor coil among these Eaton A200 Series Components is the electromagnet that closes the contactor when the controller calls for the pump to run. Coils are made for a specific supply voltage and frequency, which is why the coil section of this page is divided by voltage, from 208 volts to 600 volts, including 50 hertz and 60 hertz versions where the catalog lists them. Fitting a coil of the wrong voltage can leave the contactor chattering, failing to close, or burning out.

Auxiliary contacts fit alongside the main contactor and give the controller a signal that the contactor has closed, or switch a separate low current circuit. The Form C auxiliary contacts among these Eaton A200 Series Components are made for the model A201 contactor used in A200 series controllers. They are small parts, but a failed auxiliary contact can stop a controller from proving the pump has started.

Every part on this page is a genuine Eaton part, supplied with its Eaton part number. Eaton builds its fire pump controllers to the standards fire protection systems depend on, and using the maker’s own components keeps the controller’s ratings and approvals intact. For the manufacturer’s own fire pump control range, see Eaton fire pump controls.

How to Choose Eaton A200 Series Components

  • Match the Eaton part number to your controller model before you order. The numbers on this page are the surest way to identify the right Eaton A200 Series Components.
  • Check the contactor size before ordering a contact kit or a coil. Sizes 3, 4, 5 and 6 use different parts, and a kit for one size will not fit another.
  • Match the coil voltage and frequency to the controller supply. A 208 volt coil will not suit a 480 volt controller, and 50 hertz and 60 hertz coils are not interchangeable.
  • Note the coil style where the catalog lists one. Some 380 volt coils are marked J style or K style, and the style must match the contactor fitted.
  • Choose the auxiliary contact arrangement your controller needs: the J11 gives one normally open and one normally closed contact, while the J20 gives two normally open contacts.
  • Check whether the contact kit is a set of three or a single pole. Size 3 and size 4 kits are sets of three, while size 5 and size 6 kits are single pole parts.
  • Not sure which part fits your controller? Email sales@kbsindustries.com with the controller model, the contactor size and the supply voltage, and the part you need.

Order Eaton A200 Series Components from KBS Industries

To order Eaton A200 Series Components, email sales@kbsindustries.com with the Eaton part numbers you need and the quantity for each. KBS Industries will confirm availability and delivery for your order.

For related Eaton parts, see Eaton Electric Common Components, and for the whole fire pump control range, return to the Eaton Fire Pump Control Spares hub page.